compnaies which offers civil engg. softeares training centre franchise in india?
structural designing software
u just go through yellow pages and apply for suitable post and learn softwares appropriately
Subscribe to this blog's RSS feed
I’m going to design a long slab (80m by 20m) in hot Regen (Temp, Def, More than 40 Co) how can make the design
High bulindig (H=+35m, L 80m and W20m)
dT=40Co ocncrete frame building + shear walls
The spelling mistakes make it very difficult to interpret this question. Also you left out information. Which is why you are getting no answers.
I’ll try to interpret.
I’m designing a concrete slab 80m x 20m is a hot region, where the temperatures go above 40C. How do I do this design.
But I can’t understand the next two parts.
Bottom line, you need a structural engineer. You can not trust information on this forum in situations where someone’s life could be put in danger, which is what would happen if you designed a building with incorrect information.
What is the correct definition of development length of rebar?
also if you can plz explain difference between development length and lap splices, I am a rebar detailer, they have two seperate tables for devlpmnt length and lap splice, please explain.
Development length is additional length of rebar where anchorage is necessary. It is usually at the end of the reinforcement. It is usually 12D where D is the nominal diameter of the reinforcement. Development length also depends in the angle of anchorage
While lap splice is the length necessary when you are overalapping reinforcement for continuity and is usually 50D where D is the nominal diameter of the reinforcement.
House footing drain- How much slope is needed?
All details show the pipe at or near the bottom of the footing so how does the water get carried away?
All the details show the pipe at or near the bottom of the footing. Why is it always shown at that point? Is that the starting point or the ending point? Can I start 2′ higher than the bottom of the beam or do I start at the bottom of the beam and go down? P.S. 1/8" per 12" is adequate for the slope.
a quarter inch per foot
What is the best filler for the driveway?
Our driveway consists of two strips of concrete, with grass/dirt in the middle. My lawn and the neighbors lawn surrounds the driveway. Due to alot of rain and ppl having trouble staying on the concrete while backing up, the grass/dirt has been dug up leaving a muddy mess. What is the best thing to use to fill the holes and prevent the mess from happening again?
get it flagged
how can I build an inexpensive retaining wall without it looking cheap?
I have a planter with about 6inches of dirt. I want to build a retaining wall so I can plant small bushes and plants. Of course i’m on a small budget.
You are NOT going to believe this:
http://www.alpharubicon.com/prepinfo/quickwallscenturion.htm
How can a decorative design complement a structural design ?
What is the function of the item? Then what is the feature of the item? Then you decide what is pleasing in feature and function and come up with a decorative compliment.
How many people died during the construction of the Golden Gate Bridge?
I’ve been trying to find online how many people died during the construction of the Golden Gate Bridge but it keeps saying 11 people then 10 more people?? does that mean 21 altogether or is it just 11?
Strauss, head of the project, innovated the use of movable safety netting beneath the construction site, which saved the lives of many otherwise-unprotected steelworkers. Of eleven men killed from falls during construction, ten were killed (when the bridge was near completion) when the net failed under the stress of a scaffold that had fallen. Nineteen others who were saved by the net over the course of construction became proud members of the (informal) Halfway to Hell Club.
What’s a good type/ brand work pant for doing masonry work?
I am planning a project of replacing a front and side yard chain link fence with brick columns and wrought iron railings and gates. What’s a good type/ brand work pant for doing such down and dirty masonry work?
carhartt is an excellent work pant
Which is the best software to start learning 3 designing/animation?
I have been usiing program slike photoshop sinse long time. I got in interested in 3d modelling i can make like awesome buildings in sketchup i also made my school. But that only limits me to static and only structural models. So like could u recommend me some software with which i could start and then maybe switch over to some other one?
Blender 3d
3d’s Max
Cinema 4d
Autodesk Maya
Lightwave 3d
Bryce 3d
preferably blender 3d cus its free but if money’s no option try autodesk maya